|
Author |
Message |
kiwidave
Moderator
Joined: Mar 15th, '09, 13:14 Posts: 723
|
Re: AFX Hobby
You will have to let me know what the Super 3 car goes like. Should be really fast that one!
|
Jun 2nd, '09, 19:29 |
|
|
Swivel
Site Admin
Joined: Jul 25th, '08, 11:55 Posts: 897 Location: Hastings
|
Re: AFX Hobby
Will do. Then back in the box lol
|
Jun 2nd, '09, 20:34 |
|
|
SnuffyTech
Joined: May 13th, '09, 20:25 Posts: 30
|
Re: AFX Hobby
Swivel,
Did you get your Super3 cars in the post yet? How do they run? you got all the good ones damn you I'm not really into Nascar, but if the chassis good it might be worth a look.
|
Jun 7th, '09, 15:57 |
|
|
Swivel
Site Admin
Joined: Jul 25th, '08, 11:55 Posts: 897 Location: Hastings
|
Re: AFX Hobby
Yep. Turned up.
Goes very nice, Hugs the track, Alot faster than the afx mag chassis, as it's like the tomy chassis.
|
Jun 7th, '09, 16:17 |
|
|
kiwidave
Moderator
Joined: Mar 15th, '09, 13:14 Posts: 723
|
Re: AFX Hobby
How does it compare to a Tyco 440 chassis????
|
Jun 7th, '09, 16:20 |
|
|
Swivel
Site Admin
Joined: Jul 25th, '08, 11:55 Posts: 897 Location: Hastings
|
Re: AFX Hobby
Ahh now thats different.
Super 3 = Holden
Tyco 440 = Ford
And you know fords win. It no way as fast as the 440's I have here.
|
Jun 7th, '09, 16:50 |
|
|
kiwidave
Moderator
Joined: Mar 15th, '09, 13:14 Posts: 723
|
Re: AFX Hobby
Hahaha!!! Nice, good answer!
|
Jun 7th, '09, 16:57 |
|
|
pukekohe
TC Computers Regular
Joined: Mar 16th, '09, 17:46 Posts: 362
|
Re: AFX Hobby
not sure if I should reply to last posts,I am a gentleman after all
|
Jun 7th, '09, 17:21 |
|
|
SnuffyTech
Joined: May 13th, '09, 20:25 Posts: 30
|
Re: AFX Hobby
Preemo, Finally I've fond some time where my camera and computer have been in the same place at the same time. Here's the photos of my power tracks that I promised you. It's Tomy AFX 15'' straights, with 1mm tru-rip (light gauge speaker wire) wire soldered to the terminals. Tru-rip is dirt cheap and plenty fat enough to run slot cars properly, Jaycar will sell you a 30m roll for about $16 ( http://www.jaycar.co.nz CAT. NO. WB1703). To solder to the track, 1st get a wet towel on lay the track on that. This is a rather important step that the first time I did this I didn't take into account, and it went a pear shaped. I used a rosin cored lead solder and a solder flux the first time, and it worked alright. The second time I used silver solder, it sticks to the rails at a lower temperature so less chance of melting the plastic track. I've used a Molex 4 pin connector to let me have a bit of flexibility when changing my track around, but in hindsight I think I'd just use a piece of chocolate block (or strip connector as I think it's called these days). I'd also make the wires about 30cm longer. I can't show you any photos of the power distribution block as my tracks currently in pieces as I move workshops. I set it up the same way as recommended by hoslotcarracing.com using strip connector. I'm looking to make it an integrated circuit to keep it nice and tidy.
Attachments:
power tracks (Small).JPG [ 45.76 KiB | Viewed 6160 times ]
power closeup2.JPG [ 323.94 KiB | Viewed 6160 times ]
|
Jun 9th, '09, 00:18 |
|
|
COPPERHEAD
Passed Away 23 July 2012
Joined: Mar 29th, '09, 17:31 Posts: 617
|
Re: AFX Hobby
POOR GRANT. YOU GUYS QUIT PICKING ON HIM. GRANT DO YOU WANT A TYCO THAT WILL MAKE THEM ALL BOW AT YOUR FEET? EXCEPT FOR DAVE`S GREEN MONSTER OF COURSE. NOTHING IS THAT FAST. DAVO DID YOU SHOW IT TO ANY OF THE GUYS YET?
|
Jun 9th, '09, 13:15 |
|
|
Who is online |
Users browsing this forum: No registered users and 0 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|
|